EasyJtag Suite ver.: 1.0.87.0 started.
Operating system ver.: Windows XP (build 2600, Service Pack 3).
Successefuly connected to box on COM66
Box S/N: 1717F615772588A9, ,FW Ver.: 01.47
Box Working Mode: JTAG Box.
Box Drivers version: 3.0.0.0, are OK
Z3X Card Serial : AA7A-F652 , ver: 22
Successefuly connected to box on COM66
Box S/N: 1717F615772588A9, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:917 mV
CMD Active Level:2464 mV
EMMC CID 1501003030303030300020110726589D
EMMC CSD 902701320F5903FFF6DBFFEF8A404023
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 05/2005 FW rev.0x0 HW rev.0x0
EMMC Serial #: 537986854
EMMC NAME: 000000
EMMC Capacity: 16384 MB (High Density Card)
=============================================
Extended CSD rev 1.5 (MMC 4.41)
=============================================
Card Supported Command sets [S_CMD_SET: 0x01]
HPI Features [HPI_FEATURE: 0x03]:
implementation based on CMD12
Background operations support [BKOPS_SUPPORT: 0x01]
Background operations status [BKOPS_STATUS: 0x00]
TRIM Multiplier [TRIM_MULT: 0x01]
Secure Feature support [SEC_FEATURE_SUPPORT: 0x15]
Secure Erase Multiplier [SEC_ERASE_MULT: 0x04]
Secure TRIM Multiplier [SEC_TRIM_MULT: 0x07]
Boot Information [BOOT_INFO: 0x07]
Device supports alternative boot method
Device supports dual data rate during boot
Device supports high speed timing during boot
Boot partition size [BOOT_SIZE_MULTI: 0x04]
Access size [ACC_SIZE: 0x08]
High-capacity erase unit size [HC_ERASE_GRP_SIZE: 0x01]
High-capacity erase timeout [ERASE_TIMEOUT_MULT: 0x01]
Reliable write sector count [REL_WR_SEC_C: 0x01]
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x90]
Sleep current (VCC) [S_C_VCC: 0x07]
Sleep current (VCCQ) [S_C_VCCQ: 0x07]
Sleep/awake timeout [S_A_TIMEOUT: 0x13]
Sector Count [SEC_COUNT: 0x02000000]
Partition switching timing [PARTITION_SWITCH_TIME: 0x01]
Out-of-interrupt busy timing [OUT_OF_INTERRUPT_TIME: 0x01]
Card Type [CARD_TYPE: 0x07]
CSD structure version [CSD_STRUCTURE: 0x02]
Command set [CMD_SET: 0x00]
Command set revision [CMD_SET_REV: 0x00]
Power class [POWER_CLASS: 0x00]
High-speed interface timing [HS_TIMING: 0x00]
Erased memory content [ERASED_MEM_CONT: 0x00]
Boot configuration bytes [PARTITION_CONFIG: 0x00]
Not boot enable
No access to boot partition
Boot config protection [BOOT_CONFIG_PROT: 0x00]
Boot bus Conditions [BOOT_BUS_CONDITIONS: 0x00]
High-density erase group definition [ERASE_GROUP_DEF: 0x00]
=============================================
Boot write protection status registers [BOOT_WP_STATUS]: 0x00
Boot Area Write protection [BOOT_WP]: 0x00
Power ReadOnly locking: possible
Permanent ReadOnly locking: possible
Read Only lock status: not locked
=============================================
User area write protection register [USER_WP]: 0x00
FW configuration [FW_CONFIG]: 0x00
RPMB Size [RPMB_SIZE_MULT]: 0x01
Write reliability setting register [WR_REL_SET]: 0x1f
Write reliability parameter register [WR_REL_PARAM]: 0x05
Enable background operations handshake [BKOPS_EN]: 0x00
H/W reset function [RST_N_FUNCTION]: 0x00
HPI management [HPI_MGMT]: 0x00
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Max Enhanced Area Size [MAX_ENH_SIZE_MULT]: 0xd38000
Partitions attribute [PARTITIONS_ATTRIBUTE]: 0x00
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
General Purpose Partition Size
[GP_SIZE_MULT_4]: 0x000000
[GP_SIZE_MULT_3]: 0x000000
[GP_SIZE_MULT_2]: 0x000000
[GP_SIZE_MULT_1]: 0x000000
Enhanced User Data Area Size [ENH_SIZE_MULT]: 0x000000
Enhanced User Data Start Address [ENH_START_ADDR]: 0x000000
Bad Block Management mode [SEC_BAD_BLK_MGMNT]: 0x00
Writing file...D:\EasyJtag\i9300\EMMC_ROM2_2Mb_BOOT\EMMC_R OM2_00000000_00200000.bin
Successefuly connected to box on COM66
Box S/N: 1717F615772588A9, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:917 mV
CMD Active Level:2454 mV
EMMC CID 1501003030303030300020110726589D
EMMC CSD 902701320F5903FFF6DBFFEF8A404023
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 05/2005 FW rev.0x0 HW rev.0x0
EMMC Serial #: 537986854
EMMC NAME: 000000
EMMC Capacity: 16384 MB (High Density Card)
Writing 000000200000 bytes to 00000000 ...ROM2
Retry writing adress 0x00000000
Retry writing adress 0x00000000
Retry writing adress 0x00000000
Retry writing adress 0x00000000
in most of s3 (i9300) phone same problem..... emmc name:00000
Operating system ver.: Windows XP (build 2600, Service Pack 3).
Successefuly connected to box on COM66
Box S/N: 1717F615772588A9, ,FW Ver.: 01.47
Box Working Mode: JTAG Box.
Box Drivers version: 3.0.0.0, are OK
Z3X Card Serial : AA7A-F652 , ver: 22
Successefuly connected to box on COM66
Box S/N: 1717F615772588A9, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:917 mV
CMD Active Level:2464 mV
EMMC CID 1501003030303030300020110726589D
EMMC CSD 902701320F5903FFF6DBFFEF8A404023
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 05/2005 FW rev.0x0 HW rev.0x0
EMMC Serial #: 537986854
EMMC NAME: 000000
EMMC Capacity: 16384 MB (High Density Card)
=============================================
Extended CSD rev 1.5 (MMC 4.41)
=============================================
Card Supported Command sets [S_CMD_SET: 0x01]
HPI Features [HPI_FEATURE: 0x03]:
implementation based on CMD12
Background operations support [BKOPS_SUPPORT: 0x01]
Background operations status [BKOPS_STATUS: 0x00]
TRIM Multiplier [TRIM_MULT: 0x01]
Secure Feature support [SEC_FEATURE_SUPPORT: 0x15]
Secure Erase Multiplier [SEC_ERASE_MULT: 0x04]
Secure TRIM Multiplier [SEC_TRIM_MULT: 0x07]
Boot Information [BOOT_INFO: 0x07]
Device supports alternative boot method
Device supports dual data rate during boot
Device supports high speed timing during boot
Boot partition size [BOOT_SIZE_MULTI: 0x04]
Access size [ACC_SIZE: 0x08]
High-capacity erase unit size [HC_ERASE_GRP_SIZE: 0x01]
High-capacity erase timeout [ERASE_TIMEOUT_MULT: 0x01]
Reliable write sector count [REL_WR_SEC_C: 0x01]
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x90]
Sleep current (VCC) [S_C_VCC: 0x07]
Sleep current (VCCQ) [S_C_VCCQ: 0x07]
Sleep/awake timeout [S_A_TIMEOUT: 0x13]
Sector Count [SEC_COUNT: 0x02000000]
Partition switching timing [PARTITION_SWITCH_TIME: 0x01]
Out-of-interrupt busy timing [OUT_OF_INTERRUPT_TIME: 0x01]
Card Type [CARD_TYPE: 0x07]
CSD structure version [CSD_STRUCTURE: 0x02]
Command set [CMD_SET: 0x00]
Command set revision [CMD_SET_REV: 0x00]
Power class [POWER_CLASS: 0x00]
High-speed interface timing [HS_TIMING: 0x00]
Erased memory content [ERASED_MEM_CONT: 0x00]
Boot configuration bytes [PARTITION_CONFIG: 0x00]
Not boot enable
No access to boot partition
Boot config protection [BOOT_CONFIG_PROT: 0x00]
Boot bus Conditions [BOOT_BUS_CONDITIONS: 0x00]
High-density erase group definition [ERASE_GROUP_DEF: 0x00]
=============================================
Boot write protection status registers [BOOT_WP_STATUS]: 0x00
Boot Area Write protection [BOOT_WP]: 0x00
Power ReadOnly locking: possible
Permanent ReadOnly locking: possible
Read Only lock status: not locked
=============================================
User area write protection register [USER_WP]: 0x00
FW configuration [FW_CONFIG]: 0x00
RPMB Size [RPMB_SIZE_MULT]: 0x01
Write reliability setting register [WR_REL_SET]: 0x1f
Write reliability parameter register [WR_REL_PARAM]: 0x05
Enable background operations handshake [BKOPS_EN]: 0x00
H/W reset function [RST_N_FUNCTION]: 0x00
HPI management [HPI_MGMT]: 0x00
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Max Enhanced Area Size [MAX_ENH_SIZE_MULT]: 0xd38000
Partitions attribute [PARTITIONS_ATTRIBUTE]: 0x00
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
General Purpose Partition Size
[GP_SIZE_MULT_4]: 0x000000
[GP_SIZE_MULT_3]: 0x000000
[GP_SIZE_MULT_2]: 0x000000
[GP_SIZE_MULT_1]: 0x000000
Enhanced User Data Area Size [ENH_SIZE_MULT]: 0x000000
Enhanced User Data Start Address [ENH_START_ADDR]: 0x000000
Bad Block Management mode [SEC_BAD_BLK_MGMNT]: 0x00
Writing file...D:\EasyJtag\i9300\EMMC_ROM2_2Mb_BOOT\EMMC_R OM2_00000000_00200000.bin
Successefuly connected to box on COM66
Box S/N: 1717F615772588A9, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:917 mV
CMD Active Level:2454 mV
EMMC CID 1501003030303030300020110726589D
EMMC CSD 902701320F5903FFF6DBFFEF8A404023
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 05/2005 FW rev.0x0 HW rev.0x0
EMMC Serial #: 537986854
EMMC NAME: 000000
EMMC Capacity: 16384 MB (High Density Card)
Writing 000000200000 bytes to 00000000 ...ROM2
Retry writing adress 0x00000000
Retry writing adress 0x00000000
Retry writing adress 0x00000000
Retry writing adress 0x00000000
in most of s3 (i9300) phone same problem..... emmc name:00000
via Welcome to gsm-tips http://forum.gsmhosting.com/vbb/f672/i9300-error-1745083/
Aucun commentaire:
Enregistrer un commentaire