is there any way ?..........
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Nokia Lumia 620 V1.0.5149.19387]
Connecting to the target...OK
Set I/O Voltage reads as 1.80V, TCK Frequency is RTCK
Following devices are found on the JTAG chain:
Device on TAP #0: ID = 0x4F1F0F0F, IR Length = 0x04 bits
Device on TAP #1: ID = 0x207D00E1, IR Length = 0x0B bits
Total IR length: 0x000F bits
Analizing IDCODE(s) of the JTAG scan chain:
1. 0x207D00E1: Qualcomm MSM8227, H/W Rev. #2
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Nokia Lumia 620 V1.0.5149.19387]
Connecting to the dead body...OK
Detected dead body ID: 0x207D00E1 - CORRECT!
Set I/O Voltage reads as 1.81V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
WARNING: DCC Loader was unable to initialize FLASH1 chip. Error code: 0x02010035
No Resurrection Data is available for the eMMC Chip with Capacity = 0B
WARNING!!! Using Resurrection Data for the eMMC Chip with Capacity = 7,23GB
ERROR: Selected FLASH Chip was not initialized by the DCC Loader.
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Nokia Lumia 620 V1.0.5149.19387]
Connecting to the target...OK
Set I/O Voltage reads as 1.80V, TCK Frequency is RTCK
Following devices are found on the JTAG chain:
Device on TAP #0: ID = 0x4F1F0F0F, IR Length = 0x04 bits
Device on TAP #1: ID = 0x207D00E1, IR Length = 0x0B bits
Total IR length: 0x000F bits
Analizing IDCODE(s) of the JTAG scan chain:
1. 0x207D00E1: Qualcomm MSM8227, H/W Rev. #2
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Nokia Lumia 620 V1.0.5149.19387]
Connecting to the dead body...OK
Detected dead body ID: 0x207D00E1 - CORRECT!
Set I/O Voltage reads as 1.81V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
WARNING: DCC Loader was unable to initialize FLASH1 chip. Error code: 0x02010035
No Resurrection Data is available for the eMMC Chip with Capacity = 0B
WARNING!!! Using Resurrection Data for the eMMC Chip with Capacity = 7,23GB
ERROR: Selected FLASH Chip was not initialized by the DCC Loader.
via Welcome to gsm-tips http://ift.tt/1qvvWLG
Aucun commentaire:
Enregistrer un commentaire