hello
my device is bricked and dead boot i try to repair boot via emmc
but i failed and got this error
n9005 32gb
00:00:59 : eMMC Test Point Connection Module
00:00:59 : ================================================== ====
00:00:59 : ================================================== ====
00:00:59 :
00:00:59 : 1. DO NOT USE THE PHONE"S BATTERY
00:00:59 : 2. Connect the Soldered TP Connections to ATF Box
00:00:59 : 3. Disconnect the USB Cable and Wait until the
00:00:59 : the ATF Software will tell you to Connect the USB.
00:00:59 :
00:00:59 :
00:00:59 : Interface Reset OK!
00:00:59 : eMMC Access Type: SECTOR MODE
00:00:59 : eMMC Supported Voltage Range:
00:00:59 : 3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V
00:00:59 :
00:00:59 : CID : 1501004D4247344743001E0EBA0E90CD
00:00:59 : CSD : D02602641EB207FFEDB7FFDF1C80801B
00:00:59 :
00:00:59 : ERROR: EMMC_SEND_EXT_CSD (CMD8)
00:00:59 : Check GREEN Test Point Connection
00:01:40 : eMMC Test Point Connection Module
00:01:40 : ================================================== ====
00:01:40 : ================================================== ====
00:01:40 :
00:01:40 : 1. DO NOT USE THE PHONE"S BATTERY
00:01:40 : 2. Connect the Soldered TP Connections to ATF Box
00:01:40 : 3. Disconnect the USB Cable and Wait until the
00:01:40 : the ATF Software will tell you to Connect the USB.
00:01:40 :
00:02:11 : ERROR: EMMC WAS NOT Detected! (CMD1)
00:02:11 : Check your Test Point Soldering!
00:02:11 : CMD1 Reply: 0x00000000
00:02:13 : ================================================== ==
what is the problem
my device is bricked and dead boot i try to repair boot via emmc
but i failed and got this error
n9005 32gb
00:00:59 : eMMC Test Point Connection Module
00:00:59 : ================================================== ====
00:00:59 : ================================================== ====
00:00:59 :
00:00:59 : 1. DO NOT USE THE PHONE"S BATTERY
00:00:59 : 2. Connect the Soldered TP Connections to ATF Box
00:00:59 : 3. Disconnect the USB Cable and Wait until the
00:00:59 : the ATF Software will tell you to Connect the USB.
00:00:59 :
00:00:59 :
00:00:59 : Interface Reset OK!
00:00:59 : eMMC Access Type: SECTOR MODE
00:00:59 : eMMC Supported Voltage Range:
00:00:59 : 3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V
00:00:59 :
00:00:59 : CID : 1501004D4247344743001E0EBA0E90CD
00:00:59 : CSD : D02602641EB207FFEDB7FFDF1C80801B
00:00:59 :
00:00:59 : ERROR: EMMC_SEND_EXT_CSD (CMD8)
00:00:59 : Check GREEN Test Point Connection
00:01:40 : eMMC Test Point Connection Module
00:01:40 : ================================================== ====
00:01:40 : ================================================== ====
00:01:40 :
00:01:40 : 1. DO NOT USE THE PHONE"S BATTERY
00:01:40 : 2. Connect the Soldered TP Connections to ATF Box
00:01:40 : 3. Disconnect the USB Cable and Wait until the
00:01:40 : the ATF Software will tell you to Connect the USB.
00:01:40 :
00:02:11 : ERROR: EMMC WAS NOT Detected! (CMD1)
00:02:11 : Check your Test Point Soldering!
00:02:11 : CMD1 Reply: 0x00000000
00:02:13 : ================================================== ==
what is the problem
via Welcome to gsm-tips http://forum.gsmhosting.com/vbb/f609/n9005-emmc-detect-error-1937432/
Aucun commentaire:
Enregistrer un commentaire